Setup bridge for existing virtual birdge that minikube is running on

I managed to setup minikube on my system using kvm2 driver, and it seems to work. However i want to be able to launch the dashboard and access it externally, i.e. access it from another device within the network.

I ran virsh net-dumpxml minikube-net

<network>   <name>minikube-net</name>   <uuid>c382666a-6aee-48bf-bfd9-3b782c423fad</uuid>   <bridge name='virbr1' stp='on' delay='0'/>   <mac address='52:54:00:da:f8:54'/>   <dns enable='no'/>   <ip address='192.168.39.1' netmask='255.255.255.0'>     <dhcp>       <range start='192.168.39.2' end='192.168.39.254'/>     </dhcp>   </ip> </network> 

I ran ip addr

1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000     link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00     inet 127.0.0.1/8 scope host lo        valid_lft forever preferred_lft forever     inet6 ::1/128 scope host        valid_lft forever preferred_lft forever 2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP group default qlen 1000     link/ether 00:15:5d:38:01:0c brd ff:ff:ff:ff:ff:ff     inet 10.0.0.201/24 brd 10.0.0.255 scope global noprefixroute dynamic eth0        valid_lft 85622sec preferred_lft 85622sec     inet6 fe80::d286:599c:62eb:c6f1/64 scope link noprefixroute        valid_lft forever preferred_lft forever 3: virbr0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc noqueue state DOWN group default qlen 1000     link/ether 52:54:00:34:cb:78 brd ff:ff:ff:ff:ff:ff     inet 192.168.122.1/24 brd 192.168.122.255 scope global virbr0        valid_lft forever preferred_lft forever 4: virbr0-nic: <BROADCAST,MULTICAST> mtu 1500 qdisc pfifo_fast master virbr0 state DOWN group default qlen 1000     link/ether 52:54:00:34:cb:78 brd ff:ff:ff:ff:ff:ff 5: virbr1: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc noqueue state DOWN group default qlen 1000     link/ether 52:54:00:da:f8:54 brd ff:ff:ff:ff:ff:ff     inet 192.168.39.1/24 brd 192.168.39.255 scope global virbr1        valid_lft forever preferred_lft forever 6: virbr1-nic: <BROADCAST,MULTICAST> mtu 1500 qdisc pfifo_fast master virbr1 state DOWN group default qlen 1000     link/ether 52:54:00:da:f8:54 brd ff:ff:ff:ff:ff:ff 

Now first time around i edited the ifcfg-eth0 file to include following line:

BRIDGE=virbr1 

Then i created a file in same folder called ifcfg-virbr1 and added this to it:

DEVICE="virbr1" BOOTPROTO="dhcp" IPV6INIT="yes" IPV6_AUTOCONF="yes" ONBOOT="yes" TYPE="Bridge" DELAY="0" 

I rebooted the VM, in hopes that now my minikube-net will have a DHCP assigned IP address from router, unfortunately no it doesn’t. Furthermore i cannot ssh into the VM anymore.

Further info I am running a Centos 7 vm within Hyper-V (nested virtualization).

Any idea how i can setup my minikube-net so that i can access it and the internal contents from outside the network?